MS8126 v1 51 r2026-06-17-BG
	MS8126 v1_5 r2019-01-15-EN

 

MS8126 на МИКРОСИСТ е контролер, предназначен за измерване и регулиране на различни технологични величини. Той е с универсален вход за най – често срещаните термосъпротивления, термодвойки и линейни сигнали. Контролерът има възможност за четири-, три- или двупроводна схема на свързване на термосъпротивлението. MS8126 има два изолирани аналогови изхода и три дискретни изхода, с които могат да се реализират различни закони за управление – P, PI или PID (избират се програмно), 2- или 3-позиционен режим. Изходите се управляват чрез импулси с променлива продължителност (ШИМ), има възможност за задаване на различни времена за формиране на “положителен” (К1) и “отрицателен” (К2) изход. Входният сигнал, аналоговите изходи и интерфейса RS485 са изолирани един от друг и от захранването.

Всички данни се запазват в енергонезависима памет, включително и текущото състояние на контролера, т.е. след отпадане на захранващото напрежение, той влиза в същия режим на управление, в който е бил преди неговото отпадане.

Осигурено е безударно превключване между автоматичен и ръчен режим с директно наблюдение на процесната променлива (Pv), заданието (SP) и изхода (Out). Посредством функция Autotuning (самонастройка) лесно се настройват параметрите за П, ПИ или ПИД режим.

Устройството поддържа RS485, MODBUS RTU протокол.

Материалът MS8126 – PID controller with universal input and MODBUS RTU communication е публикуван за пръв път на Microsyst Shop.

MS8347 is suitable for application in systems for dosing or mixing products by weight method. The input signal is from a bridge strain gauge sensor, which is powered by the device. The sensitivity and supply voltage of the sensor are hardware fixed and are set in the Order Code.

The analog output signal, which is galvanically isolated from the input signal, transmits the measured input value. The most commonly used unified format is 0 ÷ 20 mA DC; 4 ÷ 20 mA DC; 0 ÷ 10 V DC, which is also specified in the Order Code.

The controller has four galvanically isolated from the measuring part discrete inputs: TARE, ZERO, S1 and S2, for taring and zeroing the measurement, respectively, as well as for selecting preset control set points.

The controller has three discrete outputs, which are user configurable.

Материалът MS8347 – Weight controller with analog output and MODBUS RTU communication е публикуван за пръв път на Microsyst Shop.

	MS8346 v2.1_2017-03-13_BG
	MS8346 v2.1_2017-03-13_EN

MS8346 is used in systems for dosing or mixing products by weight method. The input signal is formed by a bridge strain gauge sensor, which is powered by the device. The sensitivity and supply voltage of the sensor are hardware fixed and are set in the Order Code.

The analog output signal, which is galvanically isolated from the input signal, transmits the measured input value. The most commonly used is a unified format – 0 ÷ 20 mA DC; 4 ÷ 20 mA DC; 0 ÷ 10 V DC, which is also specified in the Order Code.

The controller has four galvanically isolated from the measuring part discrete inputs START, S1 and S2 and DUMP, designed respectively for starting the measurement, selecting preset set points with a set of parameters for dosing and starting dumping.

The controller has three discrete outputs, which are user-configurable.

Galvanically isolated from the other RS485 circuits, via MODBUS RTU communication, allows the controller to be connected to centralized monitoring and process control systems.

Материалът MS8346 – Weight controller with analog output and MODBUS RTU communication е публикуван за пръв път на Microsyst Shop.

	MS6016  r2019-06-24_BG

MS6016 is designed for measurement and control of various technological quantities. The analog input is hardware-defined and user-selectable through the request code. The input can be a linear, resistive temperature sensor, thermocouple or other on request.

The controller has the ability to programmatically enable/disable a root function during linearization of the input quantity.

The device has 4 discrete outputs – K1, K2, K3, K4. The discrete outputs implement ON/OFF control with one-way hysteresis and turn-on delay. The shutdown is immediate. All outputs have independent set points and are controlled by two own limits (setpoints) – lower ALo and upper AHi. Each of these sets for each output can be excluded from control via a parameter.

The controller also has an analog transmitter isolated output that transmits the input quantity into a unified output current or voltage signal. If analog outputs are configured, both current and voltage outputs are outputted in hardware, but they cannot operate simultaneously. The type of output is determined by a parameter. Depending on the connection, the current output can be active or passive.

MS6016 communicates via MODBUS RTU protocol, via an isolated RS485 line (option upon request), which allows remote monitoring of processes and setting of various parameters and modes of up to 32 or 256 /with a special driver/ connected controllers (without repeater).

The controller provides current-limited and galvanically protected voltages for powering transmitters and for its analog outputs.

All parameters are saved in non-volatile memory, including the current state of the controller.

Материалът MS6016 – Process indicator with rooting capability е публикуван за пръв път на Microsyst Shop.

	MS6026 & MS6126 v2_2 r2015-03-20 BG
	MS6026 & MS6126 v2_2 r2015-03-20 EN

The device is used as:

• Step ON/OFF controller – up to 4 stages and one alarm output
• Process Indicator with bar graph and five discrete outputs
• Converter of technological value into a unified analog signal or for transmission via serial MODBUS RTU protocol.

Материалът MS6026 – Process indicator with three-color bargraph and universal input е публикуван за пръв път на Microsyst Shop.

Материалът MS9045 – humidity and temperature transmitter е публикуван за пръв път на Microsyst Shop.

SR04 is a differential controller, designed for control of solar systems with one or two collectors, boiler, storage vessel and a pool. SR04 also is applicable in smaller installations, including some of those elements. SR04 can heat the boiler from different sources – solar panel, electrical heater, boiler. Heating with energy from electrical grid can be programmed in fixed time zones. There is function against locking of the pumps, manual on/off switching the outputs, trial period, actuality of the measurements, non-volatile clock.

Материалът SR 04 – Controller for solar and heating systems е публикуван за пръв път на Microsyst Shop.

	MS8220 v1.1_2019-10-22 BG
	MS8220 v1.1_2020-05-04 EN

MS8220 is a 32-bit reversible counter designed to read the number of incoming input pulses and generate a programmable output when preset values are reached. The meter has a six-digit display and a software divider / multiplier, ensuring its operation with sensors with different transmission coefficients. The configuration of the states of the counter and its functionality as a dispenser is user selectable depending on the specific application. The device has MODBUS communication and basic software for local or remote control and setup, as well as ensuring its compatibility with various HMI applications. The device is equipped with non-volatile memory, which stores the setting and readings read before turning off the power.

Материалът MS8220 – Dispenser flowmeter with counter input and MODBUS RTU communication е публикуван за пръв път на Microsyst Shop.